column 7 of the hazardous materials tableguess ethnicity by photo quiz
TP40 The portable tank must not be transported when connected with spray application equipment. For the regulatory description of the codes for special provisions, please refer to 49 CFR 172.102. The packaging may not be loaded with a material outside of the packaging's design temperature range. N73 Packagings consisting of outer wooden or fiberboard boxes with inner glass, metal or other strong containers; metal or fiber drums; kegs or barrels; or strong metal cans are authorized and need not conform to the requirements of part 178 of this subchapter. N88 Any metal part of a UN pressure receptacle in contact with the contents may not contain more than 65% copper, with a tolerance of 1%. TP25 Sulphur trioxide 99.95% pure and above may be transported in tanks without an inhibitor provided that it is maintained at a temperature equal to or above 32.5 C (90.5 F). 107 The classification of the substance is expected to vary especially with the particle size and packaging but the border lines have not been experimentally determined; appropriate classifications should be verified following the test procedures in 173.57 and 173.58 of this subchapter. The material must be packaged so that the percentage of diluent does not fall below that stated in the approval at any time during transportation. The tank car specification may be marked to indicate a test pressure of 13.79 Bar (200 psig). developer resources. 11 The hazardous material must be packaged as either a liquid or a solid, as appropriate, depending on its physical form at 55 C (131 F) at atmospheric pressure. The toy plastic or paper caps must be in the form of sheets, strips, rolls, or individual caps; b. Column 5 references applicable requirements for bottom openings in part 178 of this subchapter. 117 If shipment of the explosive substance is to take place at a time that freezing weather is anticipated, the water contained in the explosive substance must be mixed with denatured alcohol so that freezing will not occur. N84 The maximum quantity per package is 500 g (1.1 lbs.). A210 This substance is forbidden for transport by air. 110 Fire extinguishers transported under UN1044 and oxygen cylinders transported for emergency use under UN1072 may include installed actuating cartridges (cartridges, power device of Division 1.4C or 1.4S), without changing the classification of Division 2.2, provided the aggregate quantity of deflagrating (propellant) explosives does not exceed 3.2 grams per cylinder. c. The cylinders are collected and transported by a private or a contract carrier for reconditioning, reuse or disposal. The temperature of the material at the time it is offered for transport and during transportation may not exceed 55 C (130 F). Where the quantity of hazardous materials contained as an integral element in machinery or apparatus exceeds the limits permitted by 173.222(c)(2), and the hazardous materials meet the provisions of 173.222(c), the machinery or apparatus may be transported by aircraft only with the prior approval of the Associate Administrator. Specification 110A500W tanks must be stainless steel. If they do leak, they must be overpacked in packagings conforming to the specification requirements of part 178 of this subchapter or in salvage packagings conforming to the requirements in 173.12 of this subchapter. Batteries contained in devices must be securely installed. N6 Battery fluid packaged with electric storage batteries, wet or dry, must conform to the packaging provisions of 173.159 (g) or (h) of this subchapter. Metal: 11A, 11B, 11N, 21A, 21B and 21N, b. will bring you to those results. N40 This material is not authorized in the following packagings: a. They must be classified in accordance with the procedure as set out in the Manual of Tests and Criteria, part III, section 39 (IBR, see 171.7 of this subchapter). These provisions apply only to bulk packagings. When Column 7 refers to a special provision for a hazardous material, the meaning and requirements of that special provision are as set forth in 172.102 of this subpart. TP13 Self-contained breathing apparatus must be provided when this hazardous material is transported by sea. 162 This material may be transported under the provisions of Division 4.1 only if it is packed so that at no time during transport will the percentage of diluent fall below the percentage that is stated in the shipping description. b. Thickness of stainless steel for tank shell and heads for cargo tanks and portable tanks must be the greater of 6.35 mm (0.250 inch) or the thickness required for a tank with a design pressure at least equal to 1.3 times the vapor pressure of the lading at 46 C (115 F). For transportation by aircraft, as an inner packaging of a combination packaging with a maximum gross mass of 30 kg when packaged as a limited quantity in accordance with 173.27(f). e. Transport in accordance with this special provision must be noted on the shipping paper. information or personal data. Comparative fire testing between a package as prepared for transport (including the substance to be transported) and an identical package filled with water must show that the maximum temperature measured inside the packages during testing does not differ by more than 200 C (392 F). The provisions of this special provision will be effective until January 2, 2023, unless we terminate them earlier or extend them beyond that date by notice of a final rule in the Federal Register. This training must be documented in training records required by 172.704(d). However, the hazard label corresponding to the hazard class or division may be substituted for the marking. A37 This entry applies only to a material meeting the definition in 171.8 of this subchapter for self-defense spray. The shipper must ensure that all applicable requirements of 173.185 of this subchapter are met. 123 Any explosives, blasting, type C containing chlorates must be segregated from explosives containing ammonium nitrate or other ammonium salts. 386 When transported by private motor carrier only, the following corrosive liquids may be packaged in polyethylene bottles with a capacity no greater than 3.785 L (one gallon), further packed inside an open-top, heavy wall, high density polyethylene box (i.e., crate) in a manner that the polyethylene bottles are not subjected to any superimposed weight, and the boxes must be reasonably secured against shifting within the transport vehicle and loaded so as to minimize the possibility of coming in contact with other lading: Compounds, cleaning liquid, NA1760, PG II or III; Corrosive liquid, acidic, inorganic, n.o.s., UN3264, PG II; Corrosive liquid, acidic, organic, n.o.s., UN3265, PG III; Corrosive liquid, basic, inorganic, n.o.s., UN3266, PG II; Hydrochloric acid solution, UN1789, PG II; and. When Column 7 refers to a special provision for a hazardous material, the meaning and requirements of that special provision are as set forth in 172.102 of this subpart. These special provisions are in addition to the standard packaging requirements. IBCs of type 31A and 31N are only authorized if approved by the Associate Administrator. It is not an official legal edition of the CFR. The purpose of this article is to explain the meaning of the coding system for the Special Provisions of column 7 in order to facilitate your review and understanding of them and how they may apply to your shipment of a hazardous material. 81 Polychlorinated biphenyl items, as defined in 40 CFR 761.3, for which specification packagings are impractical, may be packaged in non-specification packagings meeting the general packaging requirements of subparts A and B of part 173 of this subchapter. 5. However, the design stress limits may not exceed 25 percent of the stress for 0 temper at the maximum design temperature of the cargo tank, as specified in the Aluminum Association's Aluminum Standards and Data (IBR, see 171.7 of this subchapter). A82 The quantity limits in columns (9A) and (9B) do not apply to human or animal body parts, whole organs or whole bodies known to contain or suspected of containing an infectious substance. Shipment of packages under this special provision must be made by private or contract motor carrier. TP20 This hazardous material must only be transported in insulated tanks under a nitrogen blanket. The outside of each package must be plainly marked ARTICLES, EXPLOSIVES, N.O.S. These provisions apply only to non-bulk packagings: N3 Glass inner packagings are permitted in combination or composite packagings only if the hazardous material is free from hydrofluoric acid. The total weight of the explosive contents of the shaped charges assembled in the guns does not exceed 90.5 kg (200 pounds) per vehicle; and. b. 144 If transported as a residue in an underground storage tank (UST), as defined in 40 CFR 280.12, that has been cleaned and purged or rendered inert according to the American Petroleum Institute (API) Standard 1604 (IBR, see 171.7 of this subchapter), then the tank and this material are not subject to any other requirements of this subchapter. The Packing Group assigned will be II or III, according to the classification criteria for either Class 3 or Division 4.1, as appropriate, applied to the base material. If a package contains both lithium metal batteries and lithium ion batteries packed with and contained in equipment, then the shipping paper must indicate both UN 3091 Lithium metal batteries packed with equipment and UN 3481 Lithium ion batteries packed with equipment.. TP28 A portable tank having a minimum test pressure of 2.65 bar (265 kPa) may be used provided the calculated test pressure is 2.65 bar or less based on the MAWP of the hazardous material, as defined in 178.275 of this subchapter, where the test pressure is 1.5 times the MAWP. A portable tank may be offered for transport after the date of expiry of the last lining inspection for a period not to exceed three months for purposes of performing the next required test or inspection, after emptying but before cleaning. b. 53 Packages of these materials must bear the subsidiary risk label, EXPLOSIVE, and the subsidiary hazard class/division must be entered in parentheses immediately following the primary hazard class in the shipping description, unless otherwise provided in this subchapter or through an approval issued by the Associate Administrator, or the competent authority of the country of origin. 49 CFR -172.101 Hazardous Materials Table info - MaselliWeb However, sediments remaining in the tank that meet the definition for a hazardous material are subject to the applicable regulations of this subchapter. c. Every installed inflation cylinder, as associated equipment of the life-saving appliance, must be packed within the protective packaging of the life raft and the life raft itself must otherwise be in compliance with 173.219. d. The serial number for each cylinder must be recorded as part of the life-saving appliance service record by the U.S. Coast Guard-approved servicing facility. B46 The detachable protective housing for the loading and unloading valves of multi-unit tank car tanks must withstand tank test pressure and must be approved by the Associate Administrator. air bag inflators, air bag modules, seat-belt pretensioners, and pyromechanical devices containing Class 1 (explosive) materials or materials of other hazard classes. This entry may only be used for the transport of non-activated batteries that contain dry potassium hydroxide and that are intended to be activated prior to use by the addition of an appropriate amount of water to the individual cells. US Department of Transportation (DOT) Pipeline Hazardous Materials Safety (i) Tests must be performed on each type and size of bottle, for each manufacturing location. However this examination is required when the conditions of 180.605(f) are met. For liquids transported under ambient conditions may be calculated using the formula: d15 and d50 are the densities (in units of mass per unit volume) of the liquid at 15 C (59 F) and 50 C (122 F), respectively. 332 Magnesium nitrate hexahydrate is not subject to the requirements of this subchapter. 6 This material is poisonous-by-inhalation and must be described as an inhalation hazard under the provisions of this subchapter. The fiber drum must to be fabricated with a three ply wall, as a minimum. 101 The name of the particular substance or article must be specified. Each radiation detector must meet the following conditions: (1) The pressure in each neutron radiation detector must not exceed 105 kPa absolute at 20 C (68 F); (2) The amount of gas must not exceed 13 grams (0.45 ounces) per detector; and, (3) Each neutron radiation detector must be of welded metal construction with brazed metal to ceramic feed through assemblies. The total mass of lithium batteries contained in any package must not exceed the quantity limits in columns (9A) and (9B) for passenger aircraft or cargo aircraft, as applicable; b. These special provisions are in addition to the standard packaging requirements. 372 This entry applies to asymmetric capacitors with an energy storage capacity greater than 0.3 Wh. Lead compounds that have a solubility of 5% or less in accordance with this special provision are not subject to the requirements of this subchapter that pertain to Marine Pollutants. b. Shipping papers at all times must reflect a correct current accounting of all cylinders both full and expended. Except for transportation by aircraft, in palletized loads, a pallet box or unit load device (e.g. If the air bag inflator unit satisfactorily passes the series 6(c) test, it is not necessary to repeat the test on the air bag module. As a 172-29, 41 FR 15996, Apr. N4 For combination or composite packagings, glass inner packagings, other than ampoules, are not permitted. The capacity of each drum must not exceed 220 L (58 gallons). N20 A 5M1 multi-wall paper bag is authorized if transported in a closed transport vehicle. Note also that this exception does not apply to batteries that have been reconditioned for reuse. PDF Hazard Classifications Used in Hazmat Table, Column 3 The requirements of 173.24(g)(1) and 173.27(c) do not apply. c. A composite packaging 6PG2 (glass, porcelain or stoneware receptacles within a fiberboard box). When IBCs other than metal or rigid plastics IBCs are used, they must be offered for transportation in a closed freight container or a closed transport vehicle. 365 For manufactured instruments and articles containing mercury, see UN3506. 114 Jet perforating guns, charged, oil well, without detonator may be reclassed to Division 1.4 Compatibility Group D (1.4D) if the following conditions are met: a. Learn more about the eCFR, its status, and the editorial process. 352 Ammonium chlorite, ammonium chlorite aqueous solutions, and mixtures of a chlorite with an ammonium salt are forbidden for transport. Insulation must be at least 100 mm (3.9 inches) except that the insulation thickness may be reduced to 51 mm (2 inches) over the exterior heater coils. Cargo and portable tanks must have a design pressure of at least 1,207 kPa (175 psig). b. Gases of Division 2.3 and gases with a subsidiary risk of 5.1 must not be used as a propellant in a chemical under pressure. Refrigerated liquefied gases that are authorized to be transported in portable tanks are specified in tank instruction T75. 142 These hazardous materials may not be classified and transported unless authorized by the Associate Administrator. A metal hydride storage system installed in or intended to be installed in a vehicle or equipment or in vehicle or equipment components must be approved for transport by the Associate Administrator. (d) Used or spent battery exception. Tanks containing solidified methacrylic acid must not be reheated during transport. j. B80 Each cargo tank must have a minimum design pressure of 276 kPa (40 psig). The material is packaged in a DOT Specification 4BW240 cylinder, or in a DOT-51 portable tank. (i) Column 8: Packaging authorizations. f. The properties of mechanical strength mentioned in this special provision shall be tested using a prototype of a receptacle and/or dispenser filled to nominal capacity, by increasing the temperature until the specified pressures are reached. 40 Polyester resin kits consist of two components: A base material (either Class 3 or Division 4.1, Packing Group II or III) and an activator (organic peroxide), each separately packed in an inner packaging. Flexible, fiberboard or wooden IBCs must be sift-proof and water-resistant or be fitted with a sift-proof and water-resistant liner. You are using an unsupported browser. For portable tanks used for the transport of refrigerated liquefied helium and refrigerated liquefied atmospheric gas (except oxygen), the maximum rate at which the tank is filled must not exceed the liquid flow capacity of the pressure relief device rated at 130 percent of the portable tank's design pressure. (c) Tables of special provisions. f. Chemicals under pressure containing components forbidden for transport on both passenger and cargo aircraft in Columns (9A) and (9B) of the 172.101 Hazardous Materials Table must not be transported by air. TP27 A portable tank having a minimum test pressure of 4 bar (400 kPa) may be used provided the calculated test pressure is 4 bar or less based on the MAWP of the hazardous material, as defined in 178.275 of this subchapter, where the test pressure is 1.5 times the MAWP. The mixture for suspensions and gels typically has the following composition: 60-85% ammonium nitrate; 0-5% sodium or potassium perchlorate; 0-17% hexamine nitrate or monomethylamine nitrate; 5-30% water; 2-15% fuel; 0.5-4% thickening agent; 0-10% soluble flame suppressants; and trace additives. A chemical under pressure packaged in an aerosol dispenser must be transported under UN1950. When portable tank instruction T75 is referenced in Column (7) of the 172.101 Table, the applicable refrigerated liquefied gases are authorized to be transported in portable tanks in accordance with the requirements of 178.277 of this subchapter. individual packaging placed or stacked and secured by strapping, shrink or stretch-wrapping or other suitable means to a pallet). In accordance with Special Provision 8 in 172.102, which is referenced in Column 7 of the Hazardous Materials Table (HMT; 172.101) for the entry "UN3082, Environmentally hazardous substance, liquid, n.o.s.," a hazardous substance that is not a hazardous waste may be shipped under the shipping description "Other regulated substances . The Code of Federal Regulations (CFR) is the official legal print publication containing the codification of the general and permanent rules published in the Federal Register by the departments and agencies of the Federal Government. iv. c. Completed neutron radiation detection systems containing detectors meeting the conditions of paragraph a of this special provision must be transported as follows: (1) The detectors must be contained in a strong sealed outer casing; (2) The casing must contain include sufficient absorbent or adsorbent material to absorb or adsorb the entire gas contents; (3) The completed system must be packed in strong outer packagings capable of withstanding a 1.8 meter (5.9 feet) drop test without leakage unless a system's outer casing affords equivalent protection. 102 The ends of the detonating cord must be tied fast so that the explosive cannot escape. TP45 Each portable tank must be made of stainless steel, except that steel other than stainless steel may be used in accordance with the provisions of 173.24b(b) of this subchapter. Components classed as Division 6.1, Packing Group I, or Class 8, Packing Group I, must not be offered for transportation and transported under this description. Outage must be at least 5 percent at 98 C (208 F). TP31 This hazardous material may only be transported in tanks in the solid state. In addition, a lighter design intended to contain a non-pressurized Class 3 material is excepted from the examination and testing criteria specified in 173.308(b)(3). TP6 The tank must be equipped with a pressure release device which prevent a tank from bursting under fire engulfment conditions (the conditions prescribed in CGA pamphlet S-1.2 (see 171.7 of this subchapter) or alternative conditions approved by the Associate Administrator may be used to consider the fire engulfment condition), taking into account the properties of the hazardous material to be transported. When a specific portable tank instruction is specified by a T Code in Column (7) of the 172.101 Table for a specific hazardous material, a specification portable tank conforming to an alternative tank instruction may be used if: (A) The alternative portable tank has a higher or equivalent test pressure (for example, 4 bar when 2.65 bar is specified); (B) The alternative portable tank has greater or equivalent wall thickness (for example, 10 mm when 6 mm is specified); (C) The alternative portable tank has a pressure relief device as specified in the T Code. (7) Special Provisions (172.102) IB8, IP2, IP4 (7) The design type of the article must be subjected to the following test. Retain a copy of each notification of pilot-in-command if requested for up to 30 days Which one of the following hazardous materials is NOT excepted from the quantity limitations in 175.75? 8 A hazardous substance that is not a hazardous waste may be shipped under the shipping description Other regulated substances, liquid or solid, n.o.s., as appropriate. Energy storage capacity means the energy stored in a capacitor, as calculated according to the following equation. PDF DOT CHART 16 Hazardous Materials Markings,Labeling and Placarding Guide After filling, each glass inner packaging must be determined to be leak-tight by placing the glass inner packaging in a hot water bath at a temperature and for a period of time sufficient to ensure that an internal pressure equal to the vapor pressure of ethylene oxide at 55 C is achieved. 49 Mixtures of solids that are not subject to this subchapter and corrosive liquids may be transported under this entry without first applying the classification criteria of Class 8, provided there is no free liquid visible at the time the material is loaded or at the time the packaging or transport unit is closed. Formulations not meeting these criteria must be transported under the provisions applicable to the appropriate entry in the Organic Peroxide Table in 173.225 of this subchapter. TP5 For a portable tank used for the transport of flammable refrigerated liquefied gases or refrigerated liquefied oxygen, the maximum rate at which the portable tank may be filled must not exceed the liquid flow capacity of the primary pressure relief system rated at a pressure not exceeding 120 percent of the portable tank's design pressure. The HMT consists of 10 columns and provides information for each hazardous material listed. B14 Each bulk packaging, except a tank car or a multi-unit-tank car tank, must be insulated with an insulating material so that the overall thermal conductance at 15.5 C (60 F) is no more than 1.5333 kilojoules per hour per square meter per degree Celsius (0.075 Btu per hour per square foot per degree Fahrenheit) temperature differential. Company Name: Artisan EHS Consulting, LLC. The article, machinery, or apparatus, if unpackaged, or the packaging in which it is contained shall be marked Dangerous goods in articles or Dangerous goods in machinery or Dangerous goods in apparatus as appropriate, with the identification number UN3363. The requirements of 173.24(g)(1) and 173.27(c) do not apply. B7 Safety relief devices are not authorized on multi-unit tank car tanks. US DOT's Hazardous Materials Regulations (HMR) list more than 3,000 shipping names for regulated materialsfrom acetal to zirconium tetrachloride. Size of marking on bulk package must conform to 172.302(b) of this subchapter. Based on the volatility class determined by using ASTM D 439 and the Reid vapor pressure (RVP) of the particular gasoline, the maximum lading pressure and maximum ambient temperature permitted during the loading of gasoline may not exceed that listed in Table I. B3 MC 300, MC 301, MC 302, MC 303, MC 305, and MC 306 and DOT 406 cargo tanks and DOT 57 portable tanks are not authorized. The device must be in the vapor space when the tank is filled under maximum filling conditions. 119 This substance, when in quantities of not more than 11.5 kg (25.3 pounds), with not less than 10 percent water, by mass, also may be classed as Division 4.1, provided a negative test result is obtained when tested in accordance with test series 6(c) of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter). Interpretation Response Details. Lading in unlined tanks must be inhibited so that the corrosive effect on steel is not greater than that of hydrofluoric acid of 65 percent concentration. Lithium batteries installed in a cargo transport unit, designed only to provide power external to the transport unit must use the proper shipping name Lithium batteries installed in cargo transport unit found in the 172.101 Hazardous Materials Table. Only Specifications MC 304, MC 307 or DOT 407 cargo tank motor vehicles are authorized for transportation by vessel. 22 If the hazardous material is in dispersion in organic liquid, the organic liquid must have a flash point above 50 C (122 F). b. This entry applies to machinery or apparatus containing hazardous materials as a residue or as an integral element of the machinery or apparatus. The table follows: [Portable tank codes T1-T22 apply to liquid and solid hazardous materials of Classes 3 through 9 which are transported in portable tanks.]. user convenience only and is not intended to alter agency intent This content is from the eCFR and may include recent changes applied to the CFR. For transportation by aircraft, a telephone report in accordance with 171.15(a) is required if a fire, violent rupture, explosion or dangerous evolution of heat (i.e., an amount of heat sufficient to be dangerous to packaging or personal safety to include charring of packaging, melting of packaging, scorching of packaging, or other evidence) occurs as a direct result of a dry battery. Net weight of contents in wooden boxes, barrels or kegs may not exceed 45 kg (99 pounds). eCFR :: 49 CFR 172.101 -- Purpose and use of hazardous materials table. This includes vehicles transported in a packaging. A51 For aircraft batteries, irrespective of the quantity limitations specified in Column (9A) of the 172.101 Table or 175.75(c), wet cell batteries, UN2794 or UN2795, up to a limit of 100 kg net mass per package may be transported aboard passenger aircraft. A6 For combination packagings, if plastic inner packagings are used, they must be packed in tightly closed metal receptacles before packing in outer packagings. This is in response to your November 18, 2015 e-mail and subsequent conversations with members of my staff requesting clarification of the Hazardous Materials Regulations (HMR; 49 CFR Parts 171-180) applicable to the selection of a . B57 Class 115A tank car tanks used to transport chloroprene must be equipped with a non-reclosing pressure relief device of a diameter not less than 305 mm (12 inches) with a maximum rupture disc pressure of 310 kPa (45 psig). 129 These materials may not be classified and transported unless authorized by the Associate Administrator on the basis of results from Series 2 Test and a Series 6(c) Test from the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) on packages as prepared for transport. TP22 Lubricants for portable tank fittings (for example, gaskets, shut-off valves, flanges) must be oxygen compatible. b. (vi) Except when an organic peroxide is authorized under 173.225(g), if a hazardous material is not assigned a portable tank T Code, the hazardous material may not be transported in a portable tank unless approved by the Associate Administrator. that, for example, are used for medical, analytical, diagnostic, testing, or repair purposes. 238 Neutron radiation detectors: Neutron radiation detectors containing non-pressurized boron trifluoride gas in excess of 1 gram (0.035 ounces) and radiation detection systems containing such neutron radiation detectors as components may be transported by highway, rail, vessel, or cargo aircraft in accordance with the following: a. Additionally, the offeror must notify the carrier if the tank pressure rise exceeds 3 psig over any 24-hour period. 340 This entry applies only to the vessel transportation of nickel-metal hydride batteries as cargo. (3) Damage to terminals. 134 This entry applies only to vehicles powered by wet batteries, sodium batteries, lithium metal batteries or lithium ion batteries, and equipment powered by wet batteries or sodium batteries that are transported with these batteries installed. For continued use of approvals dated prior to January 1, 2012, see 173.308(b)(5). Bulk outer packagings must be liquid tight through design or by the use of lining materials. Insulating materials must not promote corrosion to steel when wet.
Cherokee Funeral Home Obituaries,
David Ginsberg Net Worth,
Sims 4 Adeepindigo Lot Traits,
Pick Up Lines With The Name Lee,
Raymond Chandler Army,
Articles C